06 15 00.04 Modified Wood Decking (porch decking)

06 15 00.04 Modified Wood Decking (porch decking)


Specification Details

Pages

Dimensions

8.5" x 11"

Editable

Word Doc

Usage Limit

Unlimited Projects

Section

06 15 00.04

Provided by

Instant Download

This specification is available for Instant Download

https://zerodocs.com/wp-content/uploads/2021/02/06-15-00.04-Thermally-Modified-Wood-Decking-porch-flooring.docx Download Spec
06 15 00.04 Modified Wood Decking (porch decking)

This guide specification section 06 15 00.04 Modified Wood Decking (porch decking) has been prepared by ThermoryUSA for use in the preparation of a project specification section covering Thermory thermally modified Ashwood for use as exterior decking, porch flooring, steps, and railings. Thermory decking can be used in exterior or interior locations and can be installed using hidden clips, PaCS press-and-click system, or visible fasteners, depending on the profile. All Thermory products are available unoiled or pre-oiled.

 

Specification Profile

Visit ThermoryUSA  specifications profile for the following Thermory thermally modified wood products:

06 15 00.02 – Thermally Modified Wood Decking (Pine)

06 15 00.03 – Thermally Modified Wood Decking (Spruce)

06 20 00 – Thermally Modified Finish Carpentry

07 46 23 – Thermally Modified Wood Cladding.

09 78 26 – Thermally Modified Wood Wall and Ceiling Cladding.

 

For assistance in the use of products in this section, contact Thermory USA by calling 585-250-4074 or visit their website at www.thermoryusa.com.

 

This specification has been prepared based on SimpleSpecs™ specification templates. SimpleSpecs™ Master Guide Specification system comprises a full architectural master specification that can be used to specify all project requirements. For additional information visit www.zerodocs.com

 

06 15 00.04 Modified Wood Decking (porch decking)

 

 

 

 

 

06 15 00 – THERMALLY MODIFIED WOOD DECKING
PART 1 – GENERAL
  1. SUBMITTALS
    1. Action Submittals:
      1. Product Data: Manufacturer’s descriptive data and product attributes for wood materials.
      2. Samples: [Selection samples.] [Verification samples.]
    2. SYSTEM DESCRIPTION
      1. Design Requirements:
        1. Design and install [guard rails and handrails] to resist following without damage or permanent set:
          1. [50] [__] pounds per linear foot load applied in any direction at top, transferred via attachments and supports to building structure.
          2. Concentrated [200] [__] pound load applied in any direction at any point along top, transferred via attachments and supports to building structure.
          3. Maximum deflection under loading: [L/120.] [__.]
    3. QUALITY ASSURANCE
      1. Installer Qualifications: Firm specializing in work of this Section, with minimum [2] [__] years’ experience.
      2. Mockup: Minimum [__ x __] feet. Approved mockup [may] [may not] remain as part of the Work.
      3. Slip Resistance: Average dynamic coefficient of friction of 0.44, tested to ANSI A137.1/A326.3 in wet condition.
PART 2 – PRODUCTS

MANUFACTURERS

  1. Contract Documents are based on products by ThermoryUSA, www.thermoryusa.com.
  2. Substitutions: [Refer to Division 01.] [Not permitted.]

MATERIALS

Retain the following for 1 x 4 inch White Ash decking installed with hidden clips.

      1. Thermally Modified Wood Decking:
        1. Species: White Ash.
        2. Nominal size: 1 x 4 inches.
        3. Actual size: 0.79 x 3.7 inches.
        4. Coverage: 3.7 inches.
        5. Profile: Tong and groove edges, joint end matched (JEM).
        6. Color: Exotic Brown.
        7. Surface texture: Smooth.
        8. Finish: [Unoiled.] [Pre-oiled with Cutek Extreme.]

Retain the following when a Class B fire hazard classification is required. Class A rating is available at additional cost.

        1. Fire hazard classification: Class B flame spread/smoke developed rating, tested to ASTM E84.
        2. Installation type: Hidden.
        3. Installation method: T4 clips.

**** OR ****

Retain the following for 5/4 x 5 inch Golden Brown Pine decking installed with screws.

      1. Thermally Modified Wood Decking:
        1. Species: Pine.
        2. Nominal size: 5/4 x 5 inches.
        3. Actual size: 1.02 x 4.5 inches.
        4. Coverage: 4.3 inches.
        5. Profile: Tongue and groove edges, joint end matched (JEM).
        6. Color: Golden Brown.
        7. Surface texture: Smooth.
        8. Finish: [Unoiled.] [Pre-oiled with Cutek Extreme.]

Retain the following when a Class B fire hazard classification is required. Class A rating is available at additional cost.

        1. Fire hazard classification: Class B flame spread/smoke developed rating, tested to ASTM E84.
        2. Installation type: Blind fasten.
        3. Installation method: [Screws.] [Starborn Pro Plug System.]
    1. ACCESSORIES
      1. Fasteners: Type 305 stainless steel screws.
PART 3 – EXECUTION

INSTALLATION

  1. Install in accordance with manufacturer’s instructions.
  2. Decking Installation Method: Visible screws.
  3. [Railing] [Handrail] [Steps] [and] [Trim] Installation Method: Face screws.
  4. Place decking to span two or more supports.
  5. Stagger decking end joints in adjacent rows.
  6. Anchor decking to supports.
  7. Install [railings] [handrails] [steps] [and] [trim] using face screw method.

 

 

.


Industry Resources